online service

Skype
marinoviva
Skype
serenaclin
tyre catalog - Huaen Industrial Co.,Limited
Huaen Industrial Co.,Limited

How to Change a Tire

From:huaentires    Published:2014/4/2 11:45:06


How to Change a Tire?


Have you ever been stuck on the side of the road with a flat tire? Do you want to be able to change a tire without having to ask for help? Fortunately, changing a tire is a pretty simple task, provided you're prepared and willing to exert a little effort.


Step 1: Find a flat, stable and safe place to change your tire. You need a solid, level surface that will restrict the car from rolling. If you are near a road, park as far from traffic as possible and turn on your emergency flashers (hazard lights). Avoid soft ground and hills.


Step 2: Apply the parking brake and put car into "Park" position. If you have a standard transmission, put your vehicle in first or reverse.


Step 3: Place a heavy object(e.g., rock, concrete, spare wheel, etc.) in front of the front and back tires.


Step 4: Take out the spare tire and the jack. Place the jack under the frame near the tire that you are going to change. Ensure that the jack is in contact with the metal portion of your car's frame.

  • Many cars have molded plastic along the bottom. If you don't place the jack in the right spot, it will crack the plastic when you start lifting. If you're not sure about the right place to put the jack, read your owner's manual.
  • For most modern uni-body cars, there is a small notch or mark just behind the front wheel wells, or in front of the rear wheel wells where the jack is intended to be placed.
  • For most trucks or older cars that have a frame, look to place the jack on one of the beams of the frame just behind the front tire or in front of the rear tire.


Step 5: 
Raise the jack until it is supporting (but not lifting) the car. The jack should be firmly in place against the underside of the vehicle. Check to make sure that the jack is perpendicular to the ground.


Step 6: Remove the hub cap and loosen the nuts by turning counterclockwise. Don't take them all the way off; just break the resistance. By keeping the wheel on the ground when you first loosen the nuts, you'll make that you're turning the nuts instead of the wheel.

  • Use the wrench that came with your car or a standard cross wrench. Your wrench may have different sizes of openings on different ends. A correctly-sized wrench will slip easily over the nut, but will not rattle.
  • It can take quite a lot of force to break your lug nuts free. If all else fails, you can use your body weight or stomp on the wrench (be absolutely certain you are turning it the correct way - counter clockwise).
  • A cross wrench will give you much more torque than a standard single-handled wrench.


Step 7: Pump or crank the jack to lift the tire off the ground. You need to lift it high enough to remove the flat tire and replace it with a spare.

  • As you lift, make sure that the car is stable. If you notice any instability, lower the jack and fix the problem before fully lifting the car.

  • If you notice the jack lifting at an angle or leaning, lower and reposition it so that it can lift straight up.


Step 8: Remove the nuts the rest of the way. Turn them counter clockwise until they are loose. Repeat with all lug nuts, then remove the nuts completely.


Step 9: Remove the tire. Place the flat tire under the vehicle so in the event of a jack failure the vehicle will fall on the old wheel, hopefully preventing injury. If the jack is placed on a flat, solid base, you shouldn't have any problems.

  • The tire might be stuck due to rust. You could try hitting the inside half of the tire with a rubber mallet to loosen the tire, or use the spare tire to hit the outside half.


Step 10: Place the spare tire on the hub. Take care to align the rim of the spare tire with the wheel bolts, then put on the lug nuts.


Step 11: Tighten the nuts by hand until they are all snug. They should turn easily at first.

  • Using the wrench, tighten the nuts as much as possible using a star pattern. To ensure the tire is balanced, don't completely tighten the nuts one at a time. Going in a star pattern around the tire, one nut across from another, give each nut a full turn until they are equally tight.
  • Avoid using so much force that you risk upsetting the jack. You will tighten the lug nuts again once the car is down and there is no risk of it falling.


Step 12: Lower the car without applying full weight on the tire. Tighten the nuts as much as possible.


Step 13: Lower the car to the ground fully and remove the jack. Finish tightening the nuts and replace the hubcap.


Step 14: Put the old tire in your trunk and take it to a mechanic. Get an estimate for the cost of repair. Small punctures can usually be repaired for less than $15. If the tire is not repairable, they can dispose of it properly and sell you a replacement.







Scan me About order Service process Contacts

Payment terms:T/T, L/C, Western Union, PayPal, Visa, MasterCard

Shipping way: sea shipping

The choose and buy browse/search 

Send Inquiry→Offer→Negotiation→

Order ConfirmedPay Deposit→Start Production→Production Finished→Pay Balance →Delivery →Repeat Order


Tel: +86-372-5415858

Fax: +86-372-3662282

Email: ostyres@ostyres.com

Add: East Section of Huanbin North Road,Beiguan District,Anyang City,Henan Province,China


Google Exchange Rate Ostyres